more | Ansmann Mini Failsafe Waterproof (144000010)
A failsafe device is highly recommended for electric powered radio controlled models, an absolute must for fuel powered models! The failsafe device is designed to plug directly into the throttle socket of the receiver, and to have the throttle servo connected in-line. If for any reason the signal becomes weak, or the batteries start to run low, the failsafe device will automatically cut the throttle on the model. This saves the model from running away, and doing damage to itself, or people around it. more.. | |
more | Mtroniks Micro Failsafe (MFSWP)
A *NEW* micro sized 100% waterproof inexpensive failafe for use in RC models. This new micro sized WATERPROOF failsafe is small enough to fit easily into those tight radio boxes or even just hang outside the box! It's waterproof after all!!more.. | |
more | Mirage R/C Mini Failsafe for RC Cars (EL81001)
Designed to return the throttle servo to a preset position in the event that radio signal is lost or the receiver battery voltage falls below a factory preset voltage (4v). It is recommended that full brakes be programmed as the failsafe position | |
more | Fastrax Micro Failsafe (Inteligent) (FT1002M)
An absolute must for any nitro vehicle, this microsafe could easily be the best investment you have ever made. Should your radio fail, receiver battery run dead, this unit will automatically return your throttle servo back to the tick over position avoiding possible engine and vehicle damage. | |
more | Dynamite Race Guard Micro Fail Safe (DYN2553)
Compact size: .75 x .5 x .27in
Light weight: .13oz (3.9g)
Operating voltage: 4.0V - 6.0Vmore.. | |
more | Dynamite Race Guard Fail Safe Unit (DYN2550)
The programmable fail-safe unit is designed to return your throttle to a preset brake position in the event of a signal loss to your receiver or when the receiver's input drops below 4.0 volts. | |
more | Ripmax Xtra Failsafe Intelligent (XTRA-2151)
We recommend that a Throttle Failsafe is installed in every model. If radio contact is broken between the Transmitter and Receiver, the model could potentially continue to run until it ran out of fuel! By fitting a Throttle Failsafe, if radio contact is lost, the throttle will automatically cut to a predetermined setting and the model cannot run away. | |
more | Ripmax Xtra Intelligent Failsafe (XTRA-2152)
We recommend that a Throttle Failsafe is installed in every model. If radio contact is broken between the Transmitter and Receiver, the model could potentially continue to run until it ran out of fuel! By fitting a Throttle Failsafe, if radio contact is lost, the throttle will automatically cut to a predetermined setting and the model cannot run away. This version of failsafe will also cut on detection of low battery. | |
more | Ripmax Battery Checker 4.8 Volt On Board (XTRA-2010)
LED display gives indication of receiver battery condition. If sited correctly can be seen in the air on close fly-by. | |
more | Ripmax Battery Checker 4.8 - 6 Volt (Switchable) (XTRA-2000)
LED display gives indication of receiver battery condition. If sited correctly can be seen in the air on close fly-by. This version can also be used with 5 Cell receiver packs. | |
more | Ripmax Battery Load Checker (4.8-6Volt) (XTRA-2030)
This Battery Load Tester tests the condition of 4 & 5 cell Rx batteries under load. By placing a load on the battery this Tester replicates the sort of conditions a pack will be working under once the model is airborne. The charge condition is clearly shown.
| |
more | Hitec SP1003 Remote Motor On/Off Switch With Bec (SP1003)
The SP-1003 is a remote controlled motor on-off switch designed for electric airplanes. It allows the user to start and stop the motor remotely using an availible radio channel. Featuring a prop brake for folding props and a B.E.C. function that allows the user to fly without a separate receiver battery onboard as the receiver and servos are powered by the motor battery. You can fly until the auto-cut off B.E.C. switch is activated, stopping the motor and letting you glide the aircraft to a landing | |
more | Irvine Voltspy 2 Battery Checker (VS01)
The Voltspy 2 has an LED display which gives an indication of receiver battery condition. If sited correctly can be seen in the air on close fly-by. | |
more | HPI Battery Level Indicator (308)
HPI Racing's Battery Level Indicator will give you instant information as to your vehicles battery status. Once installed, simply turn your receiver battery on and the indicator will show you the power level of your receiver battery. The battery level indicator should only be used with hump back battery packs. more.. | |
more | GWS V-Tail Mixer Unit (4460520)
Mixer unit to allow two control functions to operate together for example a V-Tail. | |
more | Mtroniks Lightweight V-tail Mixer (Vtail)
| |
more | Ripmax V Tail Mixer (VMIX2)
Mixer unit to allow two control functions to operate together for example a V-Tail. | |
more | Ripmax Xtra 2CH Mixer (XTRA-2070)
Mixer unit to allow two control functions to operate together for example a V-Tail. | |
more | Venom Speed Meter (VEN0615)
Think you're fast... prove it! With the Venom Speed Meter. Easy to install in any car or truck see on the LCD screen just how fast your car has gone and track performance changes.
more.. | |
more | Ripmax Mini Servo Tester (PRMXTEST01)
The size of a credit card – and not much thicker either! Simultaneously test multiple servos' performance using one of four test modes – Auto, End Point, Trim and Neutral Mode. Just connect a 4.8~6.0v receiver battery to begin. Five bright LED indicators follow the servo's test sequence.
| |
RC Cars, Trucks, Tanks and Boats
Search
Index
Checkout
Back